What Pressure Washer PSI Is Safe for Exposed Aggregate?
Exposed aggregate is one of the most popular driveway and patio finishes across Perth, and it's easy to see why. It's durable, slip-resistant and looks great when it's clean. But it's also easy to damage with the wrong pressure washer settings. If you've ever wondered how much pressure is too much, the short answer is this: most exposed aggregate concrete is best cleaned at between 1,500 and 2,500 PSI, using a wide fan tip and a sensible working distance.
This guide explains why that range works, what can go wrong when you exceed it, and how to get great results on Perth's sandy, sun-baked, and often mineral-stained surfaces.
Understanding Exposed Aggregate and Why It's Vulnerable
Exposed aggregate concrete is made by removing the top layer of cement paste while the slab is curing, revealing the small stones (the aggregate) beneath. These stones are held in place by the surrounding cement matrix. Over time, the cement between and around the stones is the part that's most vulnerable to erosion.
Blasting the surface with too much pressure can:
- Strip the cement paste from around the stones, leaving them loose
- Dislodge individual pebbles, creating bare pockets and a rough texture
- Etch the surface, leaving a patchy or striped appearance
- Open up the pores of the concrete so it stains and grows algae faster in future
- Damage any sealer that's been applied, reducing its protective life
Once aggregate has been dislodged, it can't simply be put back. Repairs usually involve patching or resurfacing, which is far more costly than a careful clean.
The Safe PSI Range for Exposed Aggregate
Recommended: 1,500 to 2,500 PSI
For most residential driveways, paths, and patios in good condition, this range is effective at lifting dirt, algae, and general grime without harming the surface. Start at the lower end and increase only if needed.
Newer or Older Surfaces
Newly laid exposed aggregate should generally be left to cure for at least 28 days before any pressure cleaning, and even then a gentle approach (around 1,500 PSI or less) is wise. Older or weathered surfaces, particularly those where the cement paste has already worn down, need extra care. If you can see or feel loose stones, stay at the lower end of the range or use a soft wash method instead.
Sealed Surfaces
If your aggregate has been sealed, high pressure can strip or cloud the sealer. Staying near 1,500 to 2,000 PSI and keeping the nozzle moving helps preserve the coating. Many Perth homeowners reseal every two to three years, particularly in full-sun areas where UV breaks sealers down faster.
Why Not Go Higher?
Many consumer pressure washers sold in Perth hardware stores produce 2,500 to 3,500 PSI, and commercial units can exceed 4,000 PSI. These are suited to plain broom-finished concrete or heavy industrial cleaning, not to exposed aggregate. Just because a machine can reach those numbers doesn't mean it should be used at full power on this surface.
PSI Isn't the Whole Story: Flow Rate, Nozzle, and Distance
PSI is only one part of the equation. The actual cleaning force on the surface depends on several factors working together.
Nozzle Choice
A 25-degree (green) nozzle is a good all-round choice for exposed aggregate. A 40-degree (white) nozzle is gentler and ideal for delicate or sealed areas. Avoid the 0-degree (red) nozzle entirely, as it concentrates the force into a pinpoint that can gouge the surface. The 15-degree (yellow) nozzle is also risky and should only be used by experienced operators.
Working Distance
Hold the nozzle roughly 20 to 30 centimetres from the surface. Getting closer multiplies the force dramatically. If you're starting a new area, begin further back and move closer gradually until the dirt lifts.
https://zanderzqhm388.iamarrows.com/rust-stains-on-concrete-causes-removal-and-preventionFlow Rate (Litres per Minute)
Higher flow rates help rinse away loosened dirt and algae more efficiently, which means you can often clean effectively at lower pressure. A machine with good water flow and moderate PSI is usually better for aggregate than a high-PSI machine with low flow.
Technique
Use smooth, overlapping, sweeping passes and keep the wand moving at all times. Don't hold the nozzle in one spot, and avoid stopping and starting on the surface, which can leave visible lines or "zebra stripes".
Common Perth Cleaning Challenges
Perth's climate and soil conditions create some specific issues for exposed aggregate surfaces.
- Rust and bore water stains: Many Perth properties use bore water for gardens and lawns. Iron-rich bore water leaves orange-brown stains on driveways and paths. Pressure alone won't remove these; a rust remover or suitable acidic cleaner designed for concrete is usually needed.
- Limestone and sand dust: Our sandy soils and limestone-based materials can leave fine, dusty residue and surface film that responds well to a gentle wash.
- Algae and moss in shaded areas: South-facing or shaded sections, especially during the cooler, wetter months from May to September, are prone to green growth. A low-pressure treatment with an algae-killing solution is often more effective than blasting.
- Oil and tyre marks: Driveways frequently carry vehicle stains that need a degreaser applied before rinsing.
- Leaf tannins: Stains from trees such as jacarandas and Illyarrie can mark the surface and need targeted treatment.
Step-by-Step: How to Pressure Wash Exposed Aggregate Safely
- Sweep the surface to remove loose leaves, sand, and debris.
- Test a small, hidden area first using a wide fan nozzle at around 1,500 PSI. Check that no stones are loosening.
- Pre-treat stains and algae with a suitable cleaner and allow it to dwell according to the product instructions. Don't let it dry on the surface.
- Wash in sections using even, overlapping sweeps from a consistent distance, working in one direction.
- Rinse thoroughly so no cleaning residue is left behind, and keep runoff away from garden beds and stormwater drains where possible.
- Allow to dry fully before considering resealing, which typically needs a completely dry surface and mild weather.
Signs You're Using Too Much Pressure
Stop immediately and reduce the pressure or increase your distance if you notice:
Small stones popping loose or collecting in the runoff, a rougher feel underfoot, clean "tracks" that look lighter than the surrounding surface, or a dull, chalky look developing after the surface dries. These are all early signs that the cement paste is being eroded.
Consider Soft Washing for Delicate or Older Surfaces
Soft washing uses low pressure combined with appropriate cleaning solutions to break down algae, mould, and organic grime. It's increasingly popular for exposed aggregate in 2026 because it avoids the risk of surface erosion while delivering long-lasting results, since the treatment kills growth at the source rather than just blasting it off. If your aggregate is older, has previously been damaged, or is showing loose stones, this approach is worth considering.

Environmental and Local Considerations in Perth
Water use is always a consideration in Perth, so it's worth being efficient. Washing with a machine that has good flow control can reduce waste, and cleaning on a calm day helps prevent overspray. Wash water containing detergents, algae treatments, or oils should not be directed into stormwater drains, as these can flow into local waterways such as the Swan and Canning river systems. Directing runoff onto lawn or garden areas (where suitable for the product used) or collecting it are better options. Always check current local council guidance and any water restrictions that apply to your area.
When to Call a Professional
Professional pressure cleaners have commercial-grade equipment with adjustable pressure, a range of nozzles, surface cleaners, and the experience to judge how a particular surface will respond. It's worth getting a professional involved if:
Your aggregate is newly laid, has been sealed and you want to preserve the coating, has stubborn rust or oil stains, is already showing loose or missing stones, or covers a large area where uneven results would be obvious. A professional can also recommend and apply a quality sealer after cleaning to help protect against future staining and algae.
Key Takeaways
For exposed aggregate in Perth, aim for 1,500 to 2,500 PSI, use a 25 or 40-degree nozzle, keep the wand 20 to 30 centimetres from the surface, and always test a small area first. Pair gentle pressure with the right cleaning products for rust, algae, and oil, and consider soft washing for older or delicate surfaces. Taking a careful approach protects the stones, preserves the sealer, and keeps your driveway or patio looking good for years to come.
House Washing Perth
(08) 7828 5551